Plumbing Basics: An Essential for Installing a Bathtub
Plumbing Basics: An Essential for Installing a Bathtub
Blog Article
Do you find yourself trying to find additional info concerning How to Install a Bathtub?
Mounting a bath tub isn't exactly rocket science, yet it does call for solid plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably hard task. If the old bathtub is readily easily accessible, the task can relocate speedily; if you have to open a wall to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will need an assistant to leave the old bathtub as well as set in the brand-new one. See to it you have certified yourself for the task and also are comfortable trying it. As opposed to hiring a contractor to take over a halfway-completed task, it is better to consider using one prior to you begin. Opportunities are you may need a professional plumber to make tube links.
This short article will aid you set up a brand-new bathtub in your bathroom if you have actually already acquired a brand-new tub and do not need to change the plan of your previous water pipes.
Your tools and material checklist must consist of the following:
Getting ready for the Setup
First of all, the sustaining framework provided with the bath must be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.
Removing Old Touches
If you need to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the water. After doing so, activate the taps to drain any water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the limited gain access to that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before proceeding to fit the new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, position the bath tub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the tub till the spirit level reads level.
To mount taps, fit all-time low of the outermost versatile tap adapter to the ideal supply pipeline by making a compression join; then do the exact same for the other faucet.
Turn on the water system and also examine all joints and new pipework for leakages and tighten them if needed. Fill the bathtub and additionally check the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling and also securing around the tub needs to wait until the bath tub has actually been used at least once as this will certainly settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers remain in location in between the tap and the sink. Safeguard the tap in place with the maker supplied backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to fracture an inflexible seal, causing the water to pass through the wall surface between the bathroom and also the tiling, resulting in problems with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water before sealing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that write up about A Step-by-Step Guide to Installing a Bathtub when surfing around the web. Sharing is caring. You just don't know, you may very well be doing someone a favor. I am grateful for your time. Come back soon.
Toilet overflow? Call us! Report this page